Mr. Sticky’s In-Ground Pool Repair Kit (Manual Mix)

Replace Tile Underwater, Grout, Fix Plaster Cracks, Filter holes, Tank leaks, Pumps, Plumbing

PREPARATION: 1. Clean bond area with Denatured Alcohol Swipe, roughen with 60 grit sandpaper, clean again with Swipe. 2. Remove cap by twisting counter-clockwise until tabs clear slots, then pull vertically off. 3. Affix static mixing tip to syringe by aligning the flanged end with the slot, depress tip into slot, turn clockwise to lock. 4. Immerse syringe and tip in 110˚F water for 3 minutes to soften glue. 5. Insert syringe with mixing tip into dispensing gun. 6. Squeeze the trigger of the dispensing gun to force glue to mix as it passes through the mixing tip. 7. Discard the first 3" of glue from the tip as it may not be mixed properly due to lack of initial back-pressure. 8. Apply glue to both surfaces to be bonded, press joint together leaving some glue in the joint. 5. At 70˙F the working time=30 Min, Handling strength=4 Hrs, Full Cure=24 Hrs. 6. To remove uncured glue let it cure until just after it is no longer liquid, then cut and strip off. Once glue is fully cured it is very difficult to remove.  Warmer temperatures shorten cure time, lower temps lengthen cure time. Leave tip on syringe to act as a cap as glue cures within it.

Plaster Crack and Tank Hole Repair: Cut a piece of UltraWax Relief Sheet 2” longer and 2” wider than the crack or hole. Apply mixed glue to the center of the sheet. Place the sheet over the crack or hole. Apply pressure from the non-glue side of the sheetr to force glue into crack or hole or to feather the glue around it. Remove UltraWax Relief Sheet after the glue is cured.


Pool Pump, Pipe or Cracked Fitting Repair: Turn off pressure in pipe. Cut one of the supplied patches to the proper size to fit around a leaking pipe. Clean the patch with a Denatured Alcohol Swipe, roughen with 60 grit sandpaper and clean with Swipe again. Apply glue to the patch and pipe, wrap patch around pipe. Hold patch in place with duct tape (not supplied). Remove tape after curing.

Replace Tile Underwater: Clean the dry tile above water using Denatured Alcohol Swipe. Adhere the end of a piece of long duct tape to the non-glued face of the tile. Tie the tape to a heavy object above water to support the tile vertically when lowered into the pool. Apply glue to the tile and work into the tile pores. Apply more glue to the wall where the tile will be replaced. Be sure that the wall is clean and rougened with the sandpaper. Stick the tile back onto the wall and adjust the duct tape to hold it vertically while curing. Remove tape after cure.

Replace Grout Underwater: Cut a piece of UltraWax Relief Sheet 2” wide and 2“ longer than the grout line to be applied. Put mixed glue into the ziploc bag. Cut a corner off of the bag so that it will dispense the width of grout line needed. Squeeze the glue out of the bag and into the grout line. After the glue cures a little, rub, rub matching grout onto it to give a grout appearance. Place the UltraWax sheet over the grout line. Apply pressure on the sheet to shape it. Remove UltraWax Relief Sheet after the glue is cured. For large grout jobs use the Auto-Mix Kit which dispenses a 3/16” bead 12’ long.


Includes:57gr Underwater Glue (1), Denatured Alcohol Swipes (3) Mixing Cups (3), Mixing Sticks (3), 4” x 4”  Reinforced Vinyl Patches (3), UltraWax 12” x 12” Release Sheets (3), 60 grit sandpaper (3), application bag (1) Instructions (1)

*Dispensing Gun or Caulking Gun Adapter Required*